I installed FreeBSD 9.1/amd64 into Intel NUC kit (DCCP847DYE).

As mentioned in the title, I installed FreeBSD 9.1/amd64 into Intel NUC kit (DCCP847DYE).

About this kit

Intel NUC is a small PC kit. CPU of DCCP847DYE is Celeron 847 (1.1GHz).

The following photo show you objects included in the kit.

Image

This kit includes

  • Power adapter
  • Case including a motherboard
  • Panel to attach this kit with a monitor and screws
  • Two manuals (white and yellow)
  • Emblem

Photos of the manuals are below.

ImageImageImage

This kit does not have memory and SSD. I installed these of

  • Memory: ADATA, DDR3 1333 (PC3-10600), 8GB (4GBx2)
  • SSD: Plextor, mSATA, PX-64M5M (64GB)

You can see the memory at upper side of the following photo. The SSD is at bottom side.

Image

Installing FreeBSD

I had no problem in installing. The way to install was same as that for usual PC. But I recommend to confirm that TRIM command is enabled in filesystem options of freebsd-ufs. It was disabled by default.

Performance

I did buildword to measure performance. For comparing, I did the same thing on my desktop PC. CPU of it is Celeron G540 (2.5GHz), it has 4GB memory, and the storage of it is an SATA 3.0 HDD (of HITACHI).

The following table shows how much time buildwold took in seconds with the value of -j option for make(1).

-j option DCCP847DYE My desktop PC
nothing 14,308 6,121
2 8,200 4,025
4 8,198 3,983
8 8,249 4,018

dmesg

Finally, I paste output of dmesg(8) on this kit.

Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.1-RELEASE-p4 #0: Mon Jun 17 11:42:37 UTC 2013
root@amd64-builder.daemonology.net:/usr/obj/usr/src/sys/GENERIC amd64
CPU: Intel(R) Celeron(R) CPU 847 @ 1.10GHz (1098.60-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x206a7 Family = 6 Model = 2a Stepping = 7
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xdbae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,TSCDLT,XSAVE,OSXSAVE>
AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant, performance statistics
real memory = 8589934592 (8192 MB)
avail memory = 7670992896 (7315 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <INTEL DQS77SK >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 2
ACPI Warning: FADT (revision 5) is longer than ACPI 2.0 version, truncating length 268 to 244 (20110527/tbfadt-320)
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <INTEL DQS77SK> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 550
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
Event timer "HPET3" frequency 14318180 Hz quality 440
Event timer "HPET4" frequency 14318180 Hz quality 440
Event timer "HPET5" frequency 14318180 Hz quality 440
Event timer "HPET6" frequency 14318180 Hz quality 440
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0xf7800000-0xf7bfffff,0xe0000000-0xefffffff irq 16 at device 2.0 on pci0
agp0: <SandyBridge mobile GT1 IG> on vgapci0
agp0: aperture size is 256M, detected 524284k stolen memory
pci0: <simple comms> at device 22.0 (no driver attached)
em0: <Intel(R) PRO/1000 Network Connection 7.3.2> port 0xf080-0xf09f mem 0xf7c00000-0xf7c1ffff,0xf7c29000-0xf7c29fff irq 20 at device 25.0 on pci0
em0: Using an MSI interrupt
em0: Ethernet address: ec:a8:6b:f2:31:66
ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7c28000-0xf7c283ff irq 16 at device 26.0 on pci0
usbus0: EHCI version 1.0
usbus0 on ehci0
hdac0: <Intel Panther Point HDA Controller> mem 0xf7c20000-0xf7c23fff irq 22 at device 27.0 on pci0
ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7c27000-0xf7c273ff irq 23 at device 29.0 on pci0
usbus1: EHCI version 1.0
usbus1 on ehci1
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci0: <Intel Panther Point AHCI SATA controller> port 0xf0d0-0xf0d7,0xf0c0-0xf0c3,0xf0b0-0xf0b7,0xf0a0-0xf0a3,0xf060-0xf07f mem 0xf7c26000-0xf7c267ff irq 19 at device 31.2 on pci0
ahci0: AHCI v1.30 with 6 6Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcefff,0xcf000-0xcffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: cannot reserve I/O port range
ctl: CAM Target Layer loaded
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
Timecounters tick every 1.000 msec
hdacc0: <Intel Panther Point HDA CODEC> at cad 3 on hdac0
hdaa0: <Intel Panther Point Audio Function Group> at nid 1 on hdacc0
pcm0: <Intel Panther Point (HDMI/DP 8ch)> at nid 5 on hdaa0
pcm1: <Intel Panther Point (HDMI/DP 8ch)> at nid 7 on hdaa0
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
ugen0.2: <vendor 0x8087> at usbus0
uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0
ugen1.2: <vendor 0x8087> at usbus1
uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
uhub2: 6 ports with 6 removable, self powered
uhub3: 8 ports with 8 removable, self powered
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <PLEXTOR PX-64M5M 1.02> ATA-8 SATA 3.x device
ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 61057MB (125045424 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 8582828 Hz quality 1000
Trying to mount root from ufs:/dev/ada0p2 [rw]...
em0: link state changed to UP
Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s